#Mweb modem ip address password#
Set a password for your wireless network in the blank of WPA passphrase (at least 8 numbers or letters).Next, go to V. Select Network Authentication to be WPA-PAK and select WPA Encryption to be AES. Click on Security under Wireless, please don’t check Enable WPS. Click on Wireless first then click Basi c, please change SSID (it’s the name of your Wi-Fi) to another name, only numbers or letters can be included in, and select the channel to be channel 6(or channel 1, or channel 11) then click on Apply.Ģ. If the problem still exists, please contact us !ġ. Make sure the parameters provided from your ISP are correctly input. Refresh or reload this page three times to check the WAN Status, if it shows connected, please go toģ. Power off your modem for a while and then turn the power back on.Ģ. If the WAN Status doesn’t show connected, please try these following steps.ġ. If it shows connected and have assigned an address,it means you have internet now, please skip to IV. Please go to WAN under Device Info on the left menu,check W AN status and IPV4 Address. Input the WAN IP Address and WAN Subnet Mask given by your ISP. Input the PPP Username and Password given by your ISP and click next to continue in this following page.Ĭlick on next again in the follwing pages until click on App ly/Save to save the settings. Click Next to continue as shown as below. Type in the User name and password given by ISP, and click Connect.Īfter that, all the settings are done, if you chose Bridge.Ĩ.4 For PPPoA. Then choose No, create a new connection in the following page. Step3: Select Set up a new connection anyway. Step2: Under C hoose a connection option, choose connect to the internet. Under C hange your networking settings, choose Set up a new connection or network. Step1: Go to network and sharing center from control panel.
Note ： You should dial-up in your computer. Note : In this mode, W150DD acts as only a modem, not a modem router. Click Apply/Save to save your settings in this following page. Click on next again in the follwing pages until click on App ly/Save to save the settings. If you have a fixed IP given by your ISP, please check Use the following IP address, typing in the IP address information in the blanks.Ĭlick on next to continue. Obtain an IP address automatically, if your ISP doesn’t give you a fixed IP. In the WAN Service configure page, please select the correct WAN service type and click Next.Ĩ.1 For PPPoE.Type in the username and password provided by your ISP in the following page, and then click on next to continue.Ĭlick on next again in the follwing two pages until click on apply to save the settings. Please click WAN Service first, then click Connection Settings and click Add to add a new connection.ĮoA click here. Note: PPPoE, IPoE and Bridge are included in EoA.ħ. When you have selected the right type, click on Apply/Save. Then set the correct VPI/VCI value from your ISP (Internet Service Provider) and then select the DSL link type. Then go back to Advanced Setup and choose WAN Service.Then click ATM Interface and click Add to add a new setting.Ħ. It will reboot if you change the mode form Ethernet Mode.ĥ. Click Advanced Setup first, then click connection Mode, check DSL Mode and click Apply. If you have no idea, just go to advanced settings.Ĥ. Generally, you can access internet now if you refresh this webpage several times until it shows connected. Note : If you have consulted your ISP and confirmed the connection type is PPPOE, you can set W150DD/W300D in a fast way with the followings steps: select your country and VPI/VCI, input your internet access account and password into the blanks, set a password for wireless network and hit on save. You will see this following page, you can check the connection status here. ( Note: The address bar is in the most top of the web page after opening web browser).Ģ. Leave it blank before typing in 192.168.1.1, and then press enter.
Open a web browser (IE, Firefox, Safari, etc.) and find the address bar.
Login to the management page of the router :ġ. Note :If you can access internet through W150D/W300D after setting,the DSL light should be always on. Ensure that Power is on, the LAN port which you have plugged the cable in is on, the SYS and DSL are blinking. Take an Ethernet cable to connect your computer with one of the yellow LAN ports (1, 2, 3 or 4) of the router.ģ. Connect the telephone line to the DSL port of the router.Ģ. Product line: ADSL Question category: Internet Settingsġ.
#Mweb modem ip address how to#
How to setup the ADSL Router in DSL mode?
0 kommentar(er)
